Shear Walls in Seismic Buildings: Role, Behavior, and Design Considerations

  Share :          
  63

Prepared by: Assist. Lect. Israa Al-Hasani, Al-Mustaqbal University Abstract: Shear walls are vertical concrete elements that transfer horizontal seismic forces to the foundations and reduce the lateral displacements of a building. They are designed so that the wall fails through ductile flexure rather than brittle shear. Introduction Earthquakes are among the most dangerous loads on structures, as they impose large horizontal forces that may exceed the capacity of reinforced concrete frames alone. For this reason, shear walls have emerged as one of the most efficient lateral-force-resisting systems, especially in medium-rise and high-rise buildings. What Are Shear Walls? A shear wall is a vertical structural element made of reinforced concrete. It acts as a large-section cantilever fixed at the foundation. Its function is to transfer horizontal forces caused by earthquakes and wind from the slabs to the foundations, and to resist the resulting moments and shear forces. Working Mechanism When an earthquake occurs, inertial forces develop in the mass of the building and are transmitted through the slabs (which act as rigid horizontal diaphragms) to the shear walls. The wall behaves as a flexural element, so tensile and compressive stresses develop at its edges and shear stresses develop along its section. Thanks to its high stiffness, it absorbs the largest share of the lateral forces, which relieves the columns and reduces inter-story drift, a main cause of damage to non-structural elements. Types of Shear Walls Rectangular walls: The simplest form, widely used in residential buildings. Flanged walls (T, L, I): Flanges at the ends increase stiffness and strength, and suit medium-rise buildings. Coupled walls: Two walls connected by coupling beams around openings, providing good seismic energy dissipation. Core walls: Elevator and stair shafts, which act as a closed tube with high torsional resistance. Possible Failure Modes Flexural failure: The desired mode in slender walls because it is ductile and dissipates energy well. It is ensured through boundary elements and confined reinforcement. Diagonal shear failure: A brittle and dangerous mode, usually seen in short walls. It is avoided by making the shear capacity greater than the flexural capacity. Sliding shear at the base: Occurs at construction joints or at the base of the wall if there is not enough reinforcement to resist sliding. Design and Detailing Considerations Boundary elements: Strengthening the wall ends with closely spaced ties to improve confinement and the ductility of the compressed concrete. Horizontal and vertical reinforcement: Provided at the minimum ratios specified by the codes to control cracking and resist shear. Plan distribution: Symmetry is preferred in order to reduce torsion. Vertical continuity: The wall should extend from the foundation to the roof without interruption to avoid a soft story. Openings and coupling beams: These require special detailing in high seismic zones. Foundations: They must resist the moments and concentrated forces at the base of the wall and prevent overturning. Codes and Standards Designs are based on codes such as ACI 318, ASCE 7, and Eurocode 8, in addition to applicable national codes. These codes define detailing categories (ordinary, intermediate, special) according to seismic intensity and occupancy category. Advantages and Limitations Advantages: High lateral stiffness, reduced displacements and non-structural damage, relative economy in medium-rise buildings, and good behavior proven in past earthquakes when properly designed and constructed. Limitations: Restricted architectural flexibility in space planning, increased mass and loads on the foundations, and the need for precise execution of reinforcement and confinement. Conclusion Shear walls remain a fundamental option for improving the seismic performance of buildings, provided that they are designed and detailed carefully according to the adopted code and distributed in a regular, symmetrical manner. Their success depends not only on their strength but also on their ductility, their ability to dissipate energy, and the quality of construction on site. References ACI Committee 318. Building Code Requirements for Structural Concrete (ACI 318-19) and Commentary. American Concrete Institute, 2019. ASCE/SEI 7-22. Minimum Design Loads and Associated Criteria for Buildings and Other Structures. American Society of Civil Engineers, 2022. EN 1998-1:2004. Eurocode 8: Design of Structures for Earthquake Resistance — Part 1: General Rules, Seismic Actions and Rules for Buildings. CEN. Paulay, T. and Priestley, M.J.N. Seismic Design of Reinforced Concrete and Masonry Buildings. John Wiley & Sons, 1992. Moehle, J.P. Seismic Design of Reinforced Concrete Buildings. McGraw-Hill Education, 2015. Moehle, J.P., Ghodsi, T., Hooper, J.D., Fields, D.C. and Gedhada, R. Seismic Design of Cast-in-Place Concrete Special Structural Walls and Coupling Beams: A Guide for Practicing Engineers. NEHRP Seismic Design Technical Brief No. 6, NIST GCR 11-917-11, 2011. Park, R. and Paulay, T. Reinforced Concrete Structures. John Wiley & Sons, 1975. Taranath, B.S. Structural Analysis and Design of Tall Buildings: Steel and Composite Construction. CRC Press, 2011.